Kitchens and bathrooms are the main hardest working rooms in your home. They combine water, steam, high-powered appliances and lots of sockets and lighting. That makes them the rooms where electrical planning matters most.
This guide for electrical installations explains what UK homeowners, landlords and property managers need to know before the first tile is removed, from legal requirements to safe layouts and the checks that should happen before you sign off the job.
Why Electrical Planning Comes First
Most renovation delays and cost overruns come from electrics being treated as an afterthought. Moving a sink, adding an island or fitting an electric shower can all require new circuits, a larger cable or a consumer unit upgrade.
Planning the electrics before ordering units and appliances lets you:
- Position sockets, lighting and appliances at the right heights and distances
- Avoid chasing walls or lifting floors twice
- Confirm that your existing consumer unit and supply can cope with the new load
- Keep the project compliant, insured and easier to sell later
The UK Rules You Need to Know
BS 7671 (the IET Wiring Regulations)
All fixed electrical installations in the UK should meet BS 7671, the national standard for electrical safety. It covers circuit protection, earthing, bonding, cable sizing and the special requirements for rooms containing a bath or shower. Always ask your electrician which edition and amendments they are working to, and make sure it is the current one.
Part P of the Building Regulations (England and Wales)
Part P covers electrical safety in dwellings. In England, work is generally notifiable to building control when it involves:
- Installing a new circuit
- Replacing a consumer unit (fuse box)
- Making major alterations to existing circuits in certain situations
You can notify building control yourself, or use an electrician registered with a competent person scheme such as NICEIC, NAPIT or ELECSA, who can self-certify the work. Wales follows similar rules, while Scotland and Northern Ireland have their own regulations (Scottish Building Standards and Northern Ireland’s Building Regulations), so check the requirements for your location.
Certification
On completion, you should receive an EIC for new work, or a Minor Electrical Installation Works Certificate for smaller jobs. Keep these safe: solicitors, insurers and buyers often ask for them.
Kitchen Electrical Installations
A modern kitchen can carry more electrical load than any other room. Here is what a well-planned installation typically includes.
Dedicated circuits for high-load appliances
Ovens, hobs, and sometimes dishwashers, washing machines and tumble dryers are usually best supplied by their own circuits. Dedicated circuits reduce the risk of overloaded cables and nuisance tripping. A cooker circuit must be sized to the appliance and the cable route, and a large induction hob in particular may need a heavier cable than the one it replaces.
Socket outlets and ring or radial circuits
Worktop sockets are normally on a ring final circuit or radial circuit. Plan more sockets than you think you need, and consider where small appliances such as kettles, toasters, air fryers and coffee machines will actually sit. Fitting USB sockets in convenient spots is a popular upgrade.
Lighting layers
Good kitchens use three kinds of lighting: general ceiling lighting, task lighting under wall units, and accent lighting. Use LED fittings on separate switches or dimmers so each layer can be controlled independently. If you are fitting recessed downlighters in a ceiling, check fire-rated or fire-hood options where the ceiling is part of a fire-resisting structure.
Protection with RCDs
Modern installations require 30mA RCD protection on most circuits, and on sockets that may supply outdoor equipment. A consumer unit with RCBOs (which combine overcurrent and RCD protection per circuit) means one fault will not take out your whole kitchen.
Island units and floor boxes
Islands need careful planning. Cables must be run safely through the floor, and pop-up sockets or floor boxes need appropriate protection and fixings. This is a job to specify early, before the floor is finished.
Bathroom Electrical Installations
Bathrooms are classed as special locations because electricity and water create a much higher risk of shock. The rules are stricter, and this is not a DIY area.
Understanding bathroom zones
BS 7671 divides bathrooms into zones based on how close an area is to the bath or shower:
- Zone 0: inside the bath or shower tray. Only very low voltage equipment, specifically designed for the location, is permitted.
- Zone 1: directly above the bath or shower, to a set height. Equipment must usually be at least IPX4 rated, with additional requirements in some cases.
- Zone 2: the area immediately surrounding zone 1. Light fittings must have a suitable IP rating, commonly IPX4 or higher.
- Outside zones: areas beyond zone 2 have fewer restrictions, but RCD protection and sensible placement still apply.
Standard sockets are not permitted in bathrooms, except for shaver supply units that comply with the relevant standard. Always rely on a qualified electrician to interpret the zones for your particular layout.
Electric showers
Electric showers draw a high current and need their own dedicated circuit, correctly sized cable and a double-pole isolating switch, normally a pull-cord switch located outside the zones. Because of the load, check whether your consumer unit has spare capacity and an appropriate RCD before you buy the shower.
Heated towel rails, extractor fans and underfloor heating
Each of these needs correct planning:
- Heated towel rails must be positioned and wired in line with the zones and supplied from a protected circuit.
- Extractor fans should be suitably rated for the zone and sized to the room. Many run on a timer or humidity sensor.
- Electric underfloor heating needs a correct thermostat, an RCD and careful installation beneath the finished floor, and the installer should test the heating element before and after the floor goes down.
Bonding
Where metal pipes enter a bathroom, correct protective bonding and earthing arrangements are essential. Your electrician will check that the existing earthing is adequate and that any new pipework is correctly connected.
Is Your Consumer Unit Up to the Job?
An older consumer unit, particularly one with rewirable fuses or no RCD protection, may not be suitable for a renovated kitchen or bathroom. A consumer unit upgrade is often recommended or required when adding new circuits.
Planning Your Renovation: A Practical Timeline
- Survey and design: have an electrician review your existing installation and your plans before you finalise appliances.
- First fix: cables, back boxes and circuit routes are installed before plastering and before units or floors go in.
- Second fix: sockets, switches, light fittings and appliance connections are completed after decorating and fitting.
- Testing and certification: the installation is inspected, certified, and you receive the paperwork.
Skipping any of these steps is how problems, and later expense, appear.
Choosing a Qualified Electrician
Before hiring, check that they:
- Are registered with a recognised competent person scheme
- Hold public liability insurance
- Provide a clear written quotation covering materials, labour and certification
- Will issue an EIC or equivalent on completion
- Can explain how they will comply with Part P and BS 7671
Avoid anyone who suggests skipping certification to save money. Uncertified work can invalidate home insurance and cause problems when you sell.
Landlords and Property Managers
If you let property in England, your obligations go beyond the renovation. Electrical installations in privately rented homes must generally be inspected and tested at least every five years by a qualified person, and a copy of the Electrical Installation Condition Report (EICR) provided to tenants. A renovation is a good time to make sure everything is up to standard and documented.
How London Property Inspections Can Help
London Property Inspections supports homeowners, landlords and developers across the UK with clear, professional guidance on electrical safety and property condition. Whether you need an inspection before renovation, an EICR to confirm that your existing installation is safe, or independent checks after the work is complete, our team can help you move forward with confidence and the right paperwork in hand.
A safe and efficient kitchen or bathroom starts with good planning. Following this guide for electrical installations helps you meet the UK regulations, protect your household and avoid expensive rework. Involve a qualified electrician early, insist on proper certification and treat the electrics as the foundation of the whole renovation.
Frequently Asked Questions
1. Do I need a qualified electrician for a kitchen or bathroom renovation?
Yes, in most cases. Bathrooms are special locations with stricter rules, so professional installation is strongly advised.
2. Is electrical work in a bathroom notifiable in the UK?
It depends on the work. In England, adding a new circuit, such as one for an electric shower, is notifiable wherever it is. Minor work like replacing a light fitting on an existing circuit usually is not, but it must still comply with BS 7671. If in doubt, ask a registered electrician or your local building control.
3. Can I have sockets in my bathroom?
Standard socket outlets are not allowed in UK bathrooms. The usual exception is a shaver supply unit that meets the relevant standard. For other needs, such as charging a toothbrush, plan sockets outside the bathroom or use equipment designed to comply with the regulations.
4. Do I need a new consumer unit when renovating my kitchen?
Not always, but often. If your current unit lacks RCD protection, has no spare ways, or cannot handle new appliances like an induction hob, an upgrade is usually recommended. A new consumer unit is notifiable work in England, so it must be certified.
5. What certificate should I receive after the electrical work?
Expect an Electrical Installation Certificate (EIC) for new circuits or installations, and a Minor Electrical Installation Works Certificate for smaller jobs. Notifiable work also requires a building regulations compliance certificate. Keep all of these, as you may need them for insurance or when selling.